![]() You don’t need to go through the setup process again, just make sure to update the location in the app, so you know which is which.įun fact that proves how good the coverage of even the basic eeros are: I tried to get a screenshot of the “Your eero is too far away” error message for this review. Once you have all your eero units added to your network, you can unplug them and move them if you needed. Try to place your eero up high, and keep it away from other electronics like TVs, speakers, microwaves, or other sources of interference. eero devices try to make any placement work, but it may require some trial and error to figure out what is best for your setup. I found this gave the best coverage and speeds. I put another on the other side of my 1st floor, and one on the 2nd floor. My Internet connection is in the far corner of my 1st floor, so that’s where I put my main eero. eero systems are smart about figuring out all this stuff for you, and the setup process tells you if there is an issue with your placement. If your internet connection is in the corner of your house, that’s fine too. If possible, get your main eero as central as possible. For most people, this is going to be determined by where their Internet connection is, and the layout of their house. One of the most important things to consider when you’re setting up your eero is where to put them. It really is painless and quick, which isn’t something I normally say about a consumer Wi-Fi system. Once you figure out how to get Internet into your main eero unit, the rest of the setup couldn’t be simpler. You get to pick your Wi-Fi network name, pick the room the eero is going into, and add any other eero units you have. Once you have an Internet connection plugged into your main eero unit, you can continue through the rest of the setup. Internet -> Modem/router -> eero in bridge mode Internet -> Modem/router in bridge mode -> eero Tap the Save button in the top right corner Switch your selection from Automatic (recommended) to Bridge or Manual (for those running static IP) Open the eero app and tap Settings (bottom right corner) These are the steps to get your eero’s into bridge mode: If you’re not able to get your ISP router into bridge or passthrough mode, you should put your eero into bridge mode to avoid double NAT. Once you have only a modem, or a modem/router in bridge mode, all you need to do is connect an Ethernet cable from your modem to one of the eero units The eero app has some helpful guides as part of the setup process to make sure you’re plugging the correct thing into your main eero. Refer to the documentation for your specific device for instructions. If your ISP requires their router or modem/router to stay there, your best option is to put your ISP’s router into “bridge” or passthrough mode. This should be done before trying to setup your eero system. You’ll have to check with your ISP to figure out which modem you need, and you will need them to activate it once it is installed. Renting equipment from your ISP is usually a bad deal anyway. If you are able to buy your own standalone modem, do that. If you’re using an ISP-provided or rented modem/router this can be a little tricky. You don’t want to have two devices acting as routers because you want to avoid double NAT. My ISP (Verizon FiOS) uses fiber, and I have an Optical Network Terminal (ONT) which does the same function as a coax cable or DSL modem. Most cable or DSL Internet providers require a modem, or an ISP-provided modem/router. Most people are better off replacing their existing router with the eero. The short answer is that a modem is necessary for some types of Internet connections. If you’re not sure what a modem is, or what a router does, I define some common networking terms here. This might not be your situation, but I’ll try to cover some common ones. I have Verizon FiOS, which gives me a standard Ethernet connection I can plug directly into the Eero. The goal is to give your eero an Ethernet connection to the Internet. This depends on what kind of Internet connection you have. The main thing to figure out before setup is how you are connecting the eero to the Internet. The hardest part for most people is giving the eero the right kind of Internet connection. Note the time in the top left - it literally took me 5 minutes. The above screenshots were taken in real time, as I was setting up my system. If you already have an existing account, hit the log in button in the top left. If you’ve never used an eero device before, you’ll have to setup an account. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |